Shenzhen Baiqiancheng Electronic Co.,Ltd
+86-755-86152095

Main components and functions of potting compound

Nov 15, 2024

Epoxy resin potting materials generally use low molecular liquid bisphenol A type epoxy resin, this resin viscosity is small, high epoxy value. Commonly used are E-54, E-51, E-44, E-42. In potting filled under flip chips, the gap between the chip and the substrate is very small, so the viscosity of the liquid packaging material is very low. Therefore, the use of bisphenol A type epoxy resin alone cannot meet the requirements of the product. In order to reduce the viscosity of the product and meet the performance requirements of the product, we can use a combination of resins: such as adding bisphenol F type epoxy resin with low viscosity, glycidyl ester type resin and resin ring group epoxides with high heat resistance, electrical insulation and weather resistance. Among them, the resin cyclic epoxide itself also has the function of active diluent. 3.2 Curing agent

info-486-347

Curing agent is an important component in the epoxy potting material formulation, and the properties of curing material depend largely on the structure of curing agent.

(1) Room temperature curing generally uses aliphatic polyamines as curing agents, but such curing agents are highly toxic, irritating, intense heat release, and easy to oxidize during curing and use. Therefore, it is necessary to modify the polyamine, such as the use of active hydrogen on the polyredundant amine amine group, part of the synthesis of hydroxylalkylation with epoxy group and part of the synthesis of cyanoethylation with propylene, so that the curing agent can achieve low viscosity, low toxicity, low melting point, room temperature curing and a certain toughness of the comprehensive modification effect.

(2) Acid anhydride curing agent is the most important curing agent for two-component heating curing epoxy potting-sealing material. Commonly used curing agents are liquid methyl tetrahydrophthalic anhydride, liquid methyl hexahydrophthalic anhydride, hexahydrophthalic anhydride

Acid anhydride, methyl nadic anhydride, etc. This kind of curing agent has small viscosity and large dosage, which can play the dual role of curing and diluting in the potting material formula, and the curing heat release alleviates, and the curing material has excellent comprehensive performance.

 

Curing accelerator

Two-component epoxy-anhydride potting material can generally be cured by heating for a long time at about 140 ° C. Such curing conditions not only cause energy waste, but also the components and skeleton shells in most electronic devices are difficult to withstand. The curing temperature and curing time can be reduced effectively by adding accelerators into the formula. Commonly used accelerators are: bienyldiamine, DMP-30 and other tertiary amines. Imidazole compounds and metal salts of carboxylic acids such as 2-ethyl-4-methylimidazole, 2-methylimidazole, etc., may also be used. 3.4 Coupling agent.

info-453-341

In order to increase the adhesion between silica and epoxy resin, silane coupling agent is added. Coupling agent can improve the adhesion and moisture resistance of the material. Commonly used silane coupling agents for epoxy resins are glycidyl oxide, propyl trioxysilane (KH-560), aniline-methyl-triethoxysilane, α-chloro-propyl trimethoxysilane, α-merhydryl trimethoxysilane, aniline-methyl-trimethoxysilane, diethylenediamine propyl trimethoxysilane, etc. 3.5 Active diluent

 

Using epoxy resin alone, the viscosity increases significantly after adding inorganic fillers, which is not conducive to operation and defoaming, and a certain amount of diluent is often added to increase its fluidity and permeability, and extend the use period. The diluent has active and inactive points. The inactive diluent does not participate in the curing reaction, and the addition of too much is easy to increase the shrinkage rate of the product, reduce the mechanical properties and thermal deformation of the product. The participation of active diluent in the curing reaction increases the viscosity of the reactants and has little effect on the properties of the curing products. Active diluent is selected in potting material, commonly used are: n-butyl glycidyl ether, allyl glycidyl ether, diethylhexyl glycidyl ether, phenyl glycidyl ether. 3.6 Fillers

 

The addition of fillers in potting material has obvious effect on improving some physical properties and reducing cost of epoxy resin products. Its addition can not only reduce the cost, but also reduce the thermal expansion coefficient, shrinkage rate and increase the thermal conductivity of the cured material. Commonly used fillers in epoxy potting materials are silica, alumina, silicon nitride, boron nitride and other materials. Silica is divided into crystalline, fused Angle and spherical silica. In potting materials for electronic packaging, fused spherical silica is preferred due to product requirements. 3.7 Defoamer In order to solve the problem of bubbles left on the surface of the liquid packaging material after curing, defoamer can be added. The commonly used emulsifier is emulsifying silicone oil. 3.8 Toughening agent

 

Toughening agent plays an important role in the potting material. The toughening modification of epoxy resin mainly improves its toughness by adding toughening agent and plasticizer, etc. The toughening agent has two kinds of active and inert, and the active toughening agent can participate in the reaction with the epoxy resin to increase the viscosity of the reactants, thereby increasing the toughness of the cured material. Generally, carboxylated liquid nitrile butadiene rubber is selected to form a toughened "island structure" in the system to increase the impact toughness and heat resistance of the material. 3.9 Other components In order to meet the specific technical and technological requirements of the potting parts, other components can also be added to the formula. Such as flame retardants can improve the manufacturability of materials; Colorants are used to meet product appearance requirements.